adam@adam-laptop:~/m1_adam/snapshots/2011-07-13/for-rc3$ flterm --port /dev/ttyUSB0 --kernel boot.7822c2.bin [FLTERM] Starting... libHPDMC SDRAM initialization runtime (c) Copyright 2010 Sebastien Bourdeauducq, released under GNU LGPL version 3. Version 1.0 Initialization sequence completed. Autocalibration OK, testing memory... All SDRAM initialization completed, boot continuing. VGA: framebuffers at 0x440215c0 0x441a15c0 0x443215c0 VGA: DDC I2C bus initialized VGA: mode set to 640x480 MILKYMIST(tm) v1.0 BIOS http://www.milkymist.org (c) Copyright 2007, 2008, 2009, 2010, 2011 Sebastien Bourdeauducq This program is free software: you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation, version 3 of the License. I: BIOS CRC passed (86e23684) BRD: SoC 1.0 on Milkymist One (PCB revision 2) BRD: Mem. card : Yes BRD: AC'97 : Yes BRD: PFPU : Yes BRD: TMU : Yes BRD: Ethernet : Yes BRD: FML meter : Yes BRD: Video in : Yes BRD: MIDI : Yes BRD: DMX : Yes BRD: IR : Yes BRD: USB : Yes BRD: Memtester : No TMU: texture mapping unit initialized USB: loading Navre firmware USB: starting host controller USB: HC: softusb-input v1.0 UKB: USB keyboard connected to console I: Displaying splash screen...USB: HC: Low speed device on port A USB: HC: Low speed device on port B OK I: MAC address: 10:e2:d5:00:00:7c I: Press Q or ESC to abort boot I: Aborted boot on user request BIOS> USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: VID: 093A, PID: 2510 USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Found mouse USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Retry count exceeded, disabling device. serialboot I: Attempting serial firmware loading sL5DdSMmkekro [FLTERM] Received firmware download request from the device. [FLTERM] Uploading kernel (60788 bytes)... [FLTERM] Upload complete (9.3KB/s). [FLTERM] Booting the device. [FLTERM] Done. *** Milkymist One automated tests starting... *** Select a test category below, or hit ENTER to run all tests: a: SDRAM b: GPIO c: VGA d: Memory card e: Audio f: Ethernet g: Video input h: MIDI i: DMX512 j: Infrared k: USB *** a pressed A8: [ PASSED ] A9: [ PASSED ] A10: [ PASSED ] A11: [ PASSED ] A12: [ PASSED ] Random pattern: [ PASSED ] Hammer pattern: [ PASSED ] Crosstalk pattern: [ PASSED ] *** Select a test category below, or hit ENTER to run all tests: a: SDRAM b: GPIO c: VGA d: Memory card e: Audio f: Ethernet g: Video input h: MIDI i: DMX512 j: Infrared k: USB *** b pressed SW1: Press the button. f to fail test, s to skip. [ PASSED ] SW2: Press the button. f to fail test, s to skip. [ PASSED ] SW3: Press the button. f to fail test, s to skip. [ PASSED ] LED2: Is the LED on? (y/n/s) [ PASSED ] LED3: Is the LED on? (y/n/s) [ PASSED ] *** Select a test category below, or hit ENTER to run all tests: a: SDRAM b: GPIO c: VGA d: Memory card e: Audio f: Ethernet g: Video input h: MIDI i: DMX512 j: Infrared k: USB *** c pressed DDC: [ PASSED ] Test card: Is the picture OK? (y/n/s) [ FAILED ] *** Select a test category below, or hit ENTER to run all tests: a: SDRAM b: GPIO c: VGA d: Memory card e: Audio f: Ethernet g: Video input h: MIDI i: DMX512 j: Infrared k: USB *** d pressed Card initialization: [ PASSED ] Block read: [ PASSED ] *** Select a test category below, or hit ENTER to run all tests: a: SDRAM b: GPIO c: VGA d: Memory card e: Audio f: Ethernet g: Video input h: MIDI i: DMX512 j: Infrared k: USB *** e pressed Codec probe: [ PASSED ] Line and headphones outputs: Is the test tone OK? (y/n/s/r) [ PASSED ] Microphone: Recording...Playing... Is the audio played back? (y/n/s/r) [ PASSED ] Line input: Recording...Playing... Is the audio played back? (y/n/s/r) [ PASSED ] *** Select a test category below, or hit ENTER to run all tests: a: SDRAM b: GPIO c: VGA d: Memory card e: Audio f: Ethernet g: Video input h: MIDI i: DMX512 j: Infrared k: USB *** f pressed MDIO: [ PASSED ] ARP resolution: [ PASSED ] *** Select a test category below, or hit ENTER to run all tests: a: SDRAM b: GPIO c: VGA d: Memory card e: Audio f: Ethernet g: Video input h: MIDI i: DMX512 j: Infrared k: USB *** g pressed Decoder probe: VIN: I2C bus initialized [ PASSED ] Capture: Press a key to start capturing Waiting for a captured frame. f to fail test, s to skip. LOCKS: 7 AD_RESULT: 4 Is the picture OK? (y/n) [ FAILED ] *** Select a test category below, or hit ENTER to run all tests: a: SDRAM b: GPIO c: VGA d: Memory card e: Audio f: Ethernet g: Video input h: MIDI i: DMX512 j: Infrared k: USB *** j pressed RC5 reception: Press the remote's [1] [3] [5], one by one Waiting for remote. e for exit should be [0x01], get [0x01], [0x11c1]. [1] passed should be [0x03], get [0x03], [0x19c3]. [3] passed should be [0x05], get [0x03], [0x19c3]. should be [0x05], get [0x05], [0x11c5]. [5] passed Now press 'e' exit infrared test. rx [0x19c5] [ PASSED ] *** Select a test category below, or hit ENTER to run all tests: a: SDRAM b: GPIO c: VGA d: Memory card e: Audio f: Ethernet g: Video input h: MIDI i: DMX512 j: Infrared k: USB *** i pressed DMX512 Loopback: [ PASSED ] *** Select a test category below, or hit ENTER to run all tests: a: SDRAM b: GPIO c: VGA d: Memory card e: Audio f: Ethernet g: Video input h: MIDI i: DMX512 j: Infrared k: USB *** k pressed USB Port A: USB: loading Navre firmware USB: starting host controller USB: HC: softusb-input v1.0 Press ENTER at the USB keyboard or press the left mouse button... USB: HC: Low speed device on port A USB: HC: Low speed device on port B USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: VID: 093A, PID: 2510 USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Found mouse USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Retry count exceeded, disabling device. *** Select a test category below, or hit ENTER to run all tests: a: SDRAM b: GPIO c: VGA d: Memory card e: Audio f: Ethernet g: Video input h: MIDI i: DMX512 j: Infrared k: USB *** k pressed USB Port A: Press ENTER at the USB keyboard or press the left mouse button... [ PASSED ] USB Port B: Press ENTER at the USB keyboard or press the left mouse button... [ PASSED ] *** Select a test category below, or hit ENTER to run all tests: a: SDRAM b: GPIO c: VGA d: Memory card e: Audio f: Ethernet g: Video input h: MIDI i: DMX512 j: Infrared k: USB *** k pressed USB Port A: Press ENTER at the USB keyboard or press the left mouse button... [ PASSED ] USB Port B: Press ENTER at the USB keyboard or press the left mouse button... Failed: TX: 254, but RX: 0 Failed: RX receive problem Failed: TX: 255, but RX: 0 0 ~ 255 sent out, press 'e' for exit