------------------------------------------------------------------- 1. applied fix2b circuit 2. short L3 ------------------------------------------------------------------- libHPDMC SDRAM initialization runtime (c) Copyright 2010 Sebastien Bourdeauducq, released under GNU LGPL version 3. Version 1.0 Initialization sequence completed. Autocalibration OK, testing memory... All SDRAM initialization completed, boot continuing. VGA: framebuffers at 0x440215c0 0x441a15c0 0x443215c0 VGA: DDC I2C bus initialized VGA: mode set to 640x480 MILKYMIST(tm) v1.0 BIOS http://www.milkymist.org (c) Copyright 2007, 2008, 2009, 2010, 2011 Sebastien Bourdeauducq This program is free software: you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation, version 3 of the License. I: BIOS CRC passed (86e23684) BRD: SoC 1.0 on Milkymist One (PCB revision 2) BRD: Mem. card : Yes BRD: AC'97 : Yes BRD: PFPU : Yes BRD: TMU : Yes BRD: Ethernet : Yes BRD: FML meter : Yes BRD: Video in : Yes BRD: MIDI : Yes BRD: DMX : Yes BRD: IR : Yes BRD: USB : Yes BRD: Memtester : No TMU: texture mapping unit initialized USB: loading Navre firmware USB: starting host controller USB: HC: softusb-input v1.0 UKB: USB keyboard connected to console I: Displaying splash screen...USB: HC: Low speed device on port A USB: HC: Low speed device on port B OK I: MAC address: 10:e2:d5:00:00:3a I: Press Q or ESC to abort boot I: Aborted boot on user request BIOS> USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: VID: 093A, PID: 2510 USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Found mouse USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Retry count exceeded, disabling device. serialboot I: Attempting serial firmware loading sL5DdSMmkekro *** Milkymist One automated tests starting... *** Built: Sep 16 2011 at 10:20:57 (rev ac5975c) *** Select a test category below, or hit ENTER to run all tests: a: Images b: SDRAM c: GPIO d: VGA e: Memory card f: Audio g: Ethernet h: Video input i: MIDI j: DMX512 k: Infrared l: USB *** a pressed Images CRC: standby.fpg CRC passed (got c58e8905) soc-rescue.fpg CRC passed (got 30dcc535) bios-rescue.bin CRC passed (got 56c1c797) splash-rescue.raw CRC passed (got e8ff824f) flickernoise.fbi CRC passed (got aa12a56a) soc.fpg CRC passed (got 3a31e737) bios.bin CRC passed (got 86e23684) splash.raw CRC passed (got 978f860c) flickernoise.fbi CRC passed (got aa12a56a) [  PASSED  ] *** Select a test category below, or hit ENTER to run all tests: a: Images b: SDRAM c: GPIO d: VGA e: Memory card f: Audio g: Ethernet h: Video input i: MIDI j: DMX512 k: Infrared l: USB *** b pressed A8: [  PASSED  ] A9: [  PASSED  ] A10: [  PASSED  ] A11: [  PASSED  ] A12: [  PASSED  ] Random pattern: [  PASSED  ] Hammer pattern: [  PASSED  ] Crosstalk pattern: [  PASSED  ] *** Select a test category below, or hit ENTER to run all tests: a: Images b: SDRAM c: GPIO d: VGA e: Memory card f: Audio g: Ethernet h: Video input i: MIDI j: DMX512 k: Infrared l: USB *** c pressed SW1: Press the button. f to fail test, s to skip. [  PASSED  ] SW2: Press the button. f to fail test, s to skip. [  PASSED  ] SW3: Press the button. f to fail test, s to skip. [  PASSED  ] LED2: Is the LED on? (y/n/s) [  PASSED  ] LED3: Is the LED on? (y/n/s) [  PASSED  ] *** Select a test category below, or hit ENTER to run all tests: a: Images b: SDRAM c: GPIO d: VGA e: Memory card f: Audio g: Ethernet h: Video input i: MIDI j: DMX512 k: Infrared l: USB *** d pressed DDC: [  PASSED  ] Test card: Is the picture OK? (y/n/s) [  PASSED  ] *** Select a test category below, or hit ENTER to run all tests: a: Images b: SDRAM c: GPIO d: VGA e: Memory card f: Audio g: Ethernet h: Video input i: MIDI j: DMX512 k: Infrared l: USB *** f pressed Codec probe: [  PASSED  ] Line and headphones outputs: Is the test tone OK? (y/n/s/r) [  PASSED  ] Microphone: Recording...Playing... Is the audio played back? (y/n/s/r) [  PASSED  ] Line input: Recording...Playing... Is the audio played back? (y/n/s/r) Recording...Playing... Is the audio played back? (y/n/s/r) Recording...Playing... Is the audio played back? (y/n/s/r) [  PASSED  ] *** Select a test category below, or hit ENTER to run all tests: a: Images b: SDRAM c: GPIO d: VGA e: Memory card f: Audio g: Ethernet h: Video input i: MIDI j: DMX512 k: Infrared l: USB *** g pressed MDIO: [  PASSED  ] ARP resolution: [  PASSED  ] *** Select a test category below, or hit ENTER to run all tests: a: Images b: SDRAM c: GPIO d: VGA e: Memory card f: Audio g: Ethernet h: Video input i: MIDI j: DMX512 k: Infrared l: USB *** h pressed Decoder probe: VIN: I2C bus initialized [  PASSED  ] Capture: Press a key to start capturing Waiting for a captured frame. f to fail test, s to skip. LOCKS: 7 AD_RESULT: 4 Is the picture OK? (y/n) [  PASSED  ] *** Select a test category below, or hit ENTER to run all tests: a: Images b: SDRAM c: GPIO d: VGA e: Memory card f: Audio g: Ethernet h: Video input i: MIDI j: DMX512 k: Infrared l: USB *** i pressed MIDI Loopback: press 'e' exit MIDI test 0 ~ 255 sent out, press 'e' for exit 0 ~ 255 sent out, press 'e' for exit 0 ~ 255 sent out, press 'e' for exit 0 ~ 255 sent out, press 'e' for exit 0 ~ 255 sent out, press 'e' for exit 0 ~ 255 sent out, press 'e' for exit 0 ~ 255 sent out, press 'e' for exit 0 ~ 255 sent out, press 'e' for exit [  PASSED  ] *** Select a test category below, or hit ENTER to run all tests: a: Images b: SDRAM c: GPIO d: VGA e: Memory card f: Audio g: Ethernet h: Video input i: MIDI j: DMX512 k: Infrared l: USB *** j pressed DMX512 Loopback: [  PASSED  ] *** Select a test category below, or hit ENTER to run all tests: a: Images b: SDRAM c: GPIO d: VGA e: Memory card f: Audio g: Ethernet h: Video input i: MIDI j: DMX512 k: Infrared l: USB *** k pressed RC5 reception: Press the remote's [1] [3] [5], one by one Waiting for remote. e for exit should be [0x01], get [0x01], [0x19c1]. [1] passed should be [0x03], get [0x01], [0x19c1]. should be [0x03], get [0x01], [0x19c1]. should be [0x03], get [0x01], [0x19c1]. should be [0x03], get [0x03], [0x11c3]. [3] passed should be [0x05], get [0x03], [0x11c3]. should be [0x05], get [0x03], [0x11c3]. should be [0x05], get [0x03], [0x11c3]. should be [0x05], get [0x05], [0x19c5]. [5] passed Now press 'e' exit infrared test. rx [0x19c5] Now press 'e' exit infrared test. rx [0x19c5] Now press 'e' exit infrared test. rx [0x11c5] [  PASSED  ] *** Select a test category below, or hit ENTER to run all tests: a: Images b: SDRAM c: GPIO d: VGA e: Memory card f: Audio g: Ethernet h: Video input i: MIDI j: DMX512 k: Infrared l: USB *** l pressed USB Port A: USB: loading Navre firmware USB: starting host controller USB: HC: softusb-input v1.1 Press ENTER at the USB keyboard or press the left mouse button... USB: HC: Low speed device on port A USB: HC: Low speed device on port B USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: VID: 093A, PID: 2510 USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Found mouse USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) USB: HC: Retry count exceeded, disabling device. [  PASSED  ] USB Port B: Press ENTER at the USB keyboard or press the left mouse button... [  PASSED  ] *** Select a test category below, or hit ENTER to run all tests: a: Images b: SDRAM c: GPIO d: VGA e: Memory card f: Audio g: Ethernet h: Video input i: MIDI j: DMX512 k: Infrared l: USB ------------------------------------------------------------------- 1. replaced new u17 ------------------------------------------------------------------- libHPDMC SDRAM initialization runtime (c) Copyright 2010 Sebastien Bourdeauducq, released under GNU LGPL version 3. Version 1.0 Initialization sequence completed. Autocalibration OK, testing memory... All SDRAM initialization completed, boot continuing. VGA: framebuffers at 0x440215c0 0x441a15c0 0x443215c0 VGA: DDC I2C bus initialized VGA: mode set to 640x480 MILKYMIST(tm) v1.0 BIOS http://www.milkymist.org (c) Copyright 2007, 2008, 2009, 2010, 2011 Sebastien Bourdeauducq This program is free software: you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation, version 3 of the License. I: BIOS CRC passed (86e23684) BRD: SoC 1.0 on Milkymist One (PCB revision 2) BRD: Mem. card : Yes BRD: AC'97 : Yes BRD: PFPU : Yes BRD: TMU : Yes BRD: Ethernet : Yes BRD: FML meter : Yes BRD: Video in : Yes BRD: MIDI : Yes BRD: DMX : Yes BRD: IR : Yes BRD: USB : Yes BRD: Memtester : No TMU: texture mapping unit initialized USB: loading Navre firmware USB: starting host controller USB: HC: softusb-input v1.0 UKB: USB keyboard connected to console I: Displaying splash screen...USB: HC: Low speed device on port A USB: HC: Low speed device on port B OK I: MAC address: 10:e2:d5:00:00:3a I: Press Q or ESC to abort boot I: Aborted boot on user request BIOS> USB: HC: VID: 0E6A, PID: 6001 USB: HC: VID: 093A, PID: 2510 USB: HC: Found keyboard USB: HC: Found mouse serialboot I: Attempting serial firmware loading sL5DdSMmkekro *** Milkymist One automated tests starting... *** Built: Sep 16 2011 at 10:20:57 (rev ac5975c) *** Select a test category below, or hit ENTER to run all tests: a: Images b: SDRAM c: GPIO d: VGA e: Memory card f: Audio g: Ethernet h: Video input i: MIDI j: DMX512 k: Infrared l: USB *** e pressed Card initialization: [  PASSED  ] Block read: [  PASSED  ] *** Select a test category below, or hit ENTER to run all tests: a: Images b: SDRAM c: GPIO d: VGA e: Memory card f: Audio g: Ethernet h: Video input i: MIDI j: DMX512 k: Infrared l: USB *** l pressed USB Port A: USB: loading Navre firmware USB: starting host controller USB: HC: softusb-input v1.1 Press ENTER at the USB keyboard or press the left mouse button... USB: HC: Low speed device on port A USB: HC: Low speed device on port B USB: HC: VID: 0E6A, PID: 6001 USB: HC: VID: 093A, PID: 2510 USB: HC: Found keyboard USB: HC: Found mouse [  PASSED  ] USB Port B: Press ENTER at the USB keyboard or press the left mouse button... [  PASSED  ] *** Select a test category below, or hit ENTER to run all tests: a: Images b: SDRAM c: GPIO d: VGA e: Memory card f: Audio g: Ethernet h: Video input i: MIDI j: DMX512 k: Infrared l: USB *** l pressed USB Port A: Press ENTER at the USB keyboard or press the left mouse button... [  PASSED  ] USB Port B: Press ENTER at the USB keyboard or press the left mouse button... [  PASSED  ] *** Select a test category below, or hit ENTER to run all tests: a: Images b: SDRAM c: GPIO d: VGA e: Memory card f: Audio g: Ethernet h: Video input i: MIDI j: DMX512 k: Infrared l: USB ------------------------------------------------------------------- 1. rendering and CRC test ------------------------------------------------------------------- libHPDMC SDRAM initialization runtime (c) Copyright 2010 Sebastien Bourdeauducq, released under GNU LGPL version 3. Version 1.1 Initialization sequence completed. Autocalibration OK, testing memory... All SDRAM initialization completed, boot continuing. VGA: framebuffers at 0x440215c0 0x441a15c0 0x443215c0 VGA: DDC I2C bus initialized VGA: mode set to 640x480 MILKYMIST(tm) v1.1 BIOS http://www.milkymist.org (c) Copyright 2007, 2008, 2009, 2010, 2011 Sebastien Bourdeauducq This program is free software: you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation, version 3 of the License. I: BIOS CRC passed (93a2e549) BRD: SoC 1.1 on Milkymist One (PCB revision 2) BRD: Mem. card : Yes BRD: AC'97 : Yes BRD: PFPU : Yes BRD: TMU : Yes BRD: Ethernet : Yes BRD: FML meter : Yes BRD: Video in : Yes BRD: MIDI : Yes BRD: DMX : Yes BRD: IR : Yes BRD: USB : Yes BRD: Memtester : No TMU: texture mapping unit initialized USB: loading Navre firmware USB: starting host controller USB: HC: softusb-input v1.1 UKB: USB keyboard connected to console I: Displaying splash screen...USB: HC: Low speed device on port A USB: HC: Low speed device on port B OK USB: HC: VID: 0E6A, PID: 6001 USB: HC: VID: 093A, PID: 2510 USB: HC: Found keyboard USB: HC: Found mouse I: MAC address: 10:e2:d5:00:00:3a I: Press Q or ESC to abort boot I: Booting from filesystem... E: Unable to initialize memory card driver E: Unable to initialize filesystem I: Booting from flash... I: Loading 2033436 bytes from flash... I: Booting... RTEMS SHELL (Ver.1.0-FRC):/dev/console. Nov 13 2011. 'help' to list commands. [/] # memcard_disk_init: Error: SC = 27: Initialize memory card memcard_register: Error: SC = 27: Register disk memory card driver s# syslog: ftpd: FTP daemon startedD e(v3i csee:s s/idoenvs/ pmtayx0). . /dev/pty4 (5)pseudo-terminals registered. tted (3 sessions max) telnetd started with stacksize = 81920 and priority = 9 BOOTP timeout for server 255.255.255.255 BOOTP call failed -- Connection timed out BOOTP timeout for server 255.255.255.255 BOOTP call failed -- Connection timed out BOOTP timeout for server 255.255.255.255 BOOTP call failed -- Connection timed out I I libHPDMC SDRAM initialization runtime (c) Copyright 2010 Sebastien Bourdeauducq, released under GNU LGPL version 3. Version 1.1 Initialization sequence completed. Autocalibration OK, testing memory... All SDRAM initialization completed, boot continuing. VGA: framebuffers at 0x440215c0 0x441a15c0 0x443215c0 VGA: DDC I2C bus initialized VGA: mode set to 640x480 MILKYMIST(tm) v1.1 BIOS http://www.milkymist.org (c) Copyright 2007, 2008, 2009, 2010, 2011 Sebastien Bourdeauducq This program is free software: you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation, version 3 of the License. I: BIOS CRC passed (93a2e549) BRD: SoC 1.1 on Milkymist One (PCB revision 2) BRD: Mem. card : Yes BRD: AC'97 : Yes BRD: PFPU : Yes BRD: TMU : Yes BRD: Ethernet : Yes BRD: FML meter : Yes BRD: Video in : Yes BRD: MIDI : Yes BRD: DMX : Yes BRD: IR : Yes BRD: USB : Yes BRD: Memtester : No TMU: texture mapping unit initialized USB: loading Navre firmware USB: starting host controller USB: HC: softusb-input v1.1 UKB: USB keyboard connected to console I: Displaying splash screen...USB: HC: Low speed device on port A USB: HC: Low speed device on port B OK USB: HC: VID: 0E6A, PID: 6001 USB: HC: VID: 093A, PID: 2510 USB: HC: Found keyboard USB: HC: Found mouse I: MAC address: 10:e2:d5:00:00:3a I: Press Q or ESC to abort boot I: Booting from filesystem... E: Unable to initialize memory card driver E: Unable to initialize filesystem I: Booting from flash... I: Loading 2033436 bytes from flash... I: Booting... RTEMS SHELL (Ver.1.0-FRC):/dev/console. Nov 13 2011. 'help' to list commands. [/] # memcard_disk_init: Error: SC = 27: Initialize memory card memcard_register: Error: SC = 27: Register disk memory card driver s# syslog: ftpd: FTP daemon startedD e(v3i csee:s s/idoenvs/ pmtayx0). . /dev/pty4 (5)pseudo-terminals registered. tted (3 sessions max) telnetd started with stacksize = 81920 and priority = 9 BOOTP timeout for server 255.255.255.255 BOOTP call failed -- Connection timed out BOOTP timeout for server 255.255.255.255 BOOTP call failed -- Connection timed out BOOTP timeout for server 255.255.255.255 BOOTP call failed -- Connection timed out II libHPDMC SDRAM initialization runtime (c) Copyright 2010 Sebastien Bourdeauducq, released under GNU LGPL version 3. Version 1.1 Initialization sequence completed. Autocalibration OK, testing memory... All SDRAM initialization completed, boot continuing. VGA: framebuffers at 0x440215c0 0x441a15c0 0x443215c0 VGA: DDC I2C bus initialized VGA: mode set to 640x480 MILKYMIST(tm) v1.1 BIOS http://www.milkymist.org (c) Copyright 2007, 2008, 2009, 2010, 2011 Sebastien Bourdeauducq This program is free software: you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation, version 3 of the License. I: BIOS CRC passed (93a2e549) BRD: SoC 1.1 on Milkymist One (PCB revision 2) BRD: Mem. card : Yes BRD: AC'97 : Yes BRD: PFPU : Yes BRD: TMU : Yes BRD: Ethernet : Yes BRD: FML meter : Yes BRD: Video in : Yes BRD: MIDI : Yes BRD: DMX : Yes BRD: IR : Yes BRD: USB : Yes BRD: Memtester : No TMU: texture mapping unit initialized USB: loading Navre firmware USB: starting host controller USB: HC: softusb-input v1.1 UKB: USB keyboard connected to console I: Displaying splash screen...USB: HC: Low speed device on port A USB: HC: Low speed device on port B OK USB: HC: VID: 0E6A, PID: 6001 USB: HC: VID: 093A, PID: 2510 USB: HC: Found keyboard USB: HC: Found mouse I: MAC address: 10:e2:d5:00:00:3a I: Press Q or ESC to abort boot I: Booting from filesystem... E: Unable to initialize memory card driver E: Unable to initialize filesystem I: Booting from flash... I: Loading 2033436 bytes from flash... I: Booting... RTEMS SHELL (Ver.1.0-FRC):/dev/console. Nov 13 2011. 'help' to list commands. [/] # memcard_disk_init: Error: SC = 27: Initialize memory card memcard_register: Error: SC = 27: Register disk memory card driver s# syslog: ftpd: FTP daemon startedD e(v3i csee:s s/idoenvs/ pmtayx0). . /dev/pty4 (5)pseudo-terminals registered. tted (3 sessions max) telnetd started with stacksize = 81920 and priority = 9 BOOTP timeout for server 255.255.255.255 BOOTP call failed -- Connection timed out BOOTP timeout for server 255.255.255.255 BOOTP call failed -- Connection timed out BOOTP timeout for server 255.255.255.255 BOOTP call failed -- Connection timed out BOOTP timeout for server 255.255.255.255 BOOTP call failed -- Connection timed out BOOTP timeout for server 255.255.255.255 BOOTP call failed -- Connection timed out II libHPDMC SDRAM initialization runtime (c) Copyright 2010 Sebastien Bourdeauducq, released under GNU LGPL version 3. Version 1.1 Initialization sequence completed. Autocalibration OK, testing memory... All SDRAM initialization completed, boot continuing. VGA: framebuffers at 0x440215c0 0x441a15c0 0x443215c0 VGA: DDC I2C bus initialized VGA: mode set to 640x480 MILKYMIST(tm) v1.1 BIOS http://www.milkymist.org (c) Copyright 2007, 2008, 2009, 2010, 2011 Sebastien Bourdeauducq This program is free software: you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation, version 3 of the License. I: BIOS CRC passed (93a2e549) BRD: SoC 1.1 on Milkymist One (PCB revision 2) BRD: Mem. card : Yes BRD: AC'97 : Yes BRD: PFPU : Yes BRD: TMU : Yes BRD: Ethernet : Yes BRD: FML meter : Yes BRD: Video in : Yes BRD: MIDI : Yes BRD: DMX : Yes BRD: IR : Yes BRD: USB : Yes BRD: Memtester : No TMU: texture mapping unit initialized USB: loading Navre firmware USB: starting host controller USB: HC: softusb-input v1.1 UKB: USB keyboard connected to console I: Displaying splash screen...USB: HC: Low speed device on port A USB: HC: Low speed device on port B OK USB: HC: VID: 0E6A, PID: 6001 USB: HC: VID: 093A, PID: 2510 USB: HC: Found keyboard USB: HC: Found mouse I: MAC address: 10:e2:d5:00:00:3a I: Press Q or ESC to abort boot I: Booting from filesystem... E: Unable to initialize memory card driver E: Unable to initialize filesystem I: Booting from flash... I: Loading 2033436 bytes from flash... I: Booting... RTEMS SHELL (Ver.1.0-FRC):/dev/console. Nov 13 2011. 'help' to list commands. [/] # memcard_disk_init: Error: SC = 27: Initialize memory card memcard_register: Error: SC = 27: Register disk memory card driver s# syslog: ftpd: FTP daemon startedD e(v3i csee:s s/idoenvs/ pmtayx0). . /dev/pty4 (5)pseudo-terminals registered. tted (3 sessions max) telnetd started with stacksize = 81920 and priority = 9 BOOTP timeout for server 255.255.255.255 BOOTP call failed -- Connection timed out BOOTP timeout for server 255.255.255.255 BOOTP call failed -- Connection timed out BOOTP timeout for server 255.255.255.255 BOOTP call failed -- Connection timed out libHPDMC SDRAM initialization runtime (c) Copyright 2010 Sebastien Bourdeauducq, released under GNU LGPL version 3. Version 1.1 Initialization sequence completed. Autocalibration OK, testing memory... All SDRAM initialization completed, boot continuing. VGA: framebuffers at 0x440215c0 0x441a15c0 0x443215c0 VGA: DDC I2C bus initialized VGA: mode set to 640x480 MILKYMIST(tm) v1.1 BIOS http://www.milkymist.org (c) Copyright 2007, 2008, 2009, 2010, 2011 Sebastien Bourdeauducq This program is free software: you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation, version 3 of the License. I: BIOS CRC passed (93a2e549) BRD: SoC 1.1 on Milkymist One (PCB revision 2) BRD: Mem. card : Yes BRD: AC'97 : Yes BRD: PFPU : Yes BRD: TMU : Yes BRD: Ethernet : Yes BRD: FML meter : Yes BRD: Video in : Yes BRD: MIDI : Yes BRD: DMX : Yes BRD: IR : Yes BRD: USB : Yes BRD: Memtester : No TMU: texture mapping unit initialized USB: loading Navre firmware USB: starting host controller USB: HC: softusb-input v1.1 UKB: USB keyboard connected to console I: Displaying splash screen...USB: HC: Low speed device on port A USB: HC: Low speed device on port B OK USB: HC: VID: 0E6A, PID: 6001 USB: HC: VID: 093A, PID: 2510 USB: HC: Found keyboard USB: HC: Found mouse I: MAC address: 10:e2:d5:00:00:3a I: Press Q or ESC to abort boot I: Booting from filesystem... E: Unable to initialize memory card driver E: Unable to initialize filesystem I: Booting from flash... I: Loading 2033436 bytes from flash... I: Booting... RTEMS SHELL (Ver.1.0-FRC):/dev/console. Nov 13 2011. 'help' to list commands. [/] # memcard_disk_init: Error: SC = 27: Initialize memory card memcard_register: Error: SC = 27: Register disk memory card driver s# syslog: ftpd: FTP daemon startedD e(v3i csee:s s/idoenvs/ pmtayx0). . /dev/pty4 (5)pseudo-terminals registered. tted (3 sessions max) telnetd started with stacksize = 81920 and priority = 9 BOOTP timeout for server 255.255.255.255 BOOTP call failed -- Connection timed out BOOTP timeout for server 255.255.255.255 BOOTP call failed -- Connection timed out BOOTP timeout for server 255.255.255.255 BOOTP call failed -- Connection timed out BOOTP timeout for server 255.255.255.255 BOOTP call failed -- Connection timed out II@ libHPDMC SDRAM initialization runtime (c) Copyright 2010 Sebastien Bourdeauducq, released under GNU LGPL version 3. Version 1.1 Initialization sequence completed. Autocalibration OK, testing memory... All SDRAM initialization completed, boot continuing. VGA: framebuffers at 0x440215c0 0x441a15c0 0x443215c0 VGA: DDC I2C bus initialized VGA: mode set to 640x480 MILKYMIST(tm) v1.1 BIOS http://www.milkymist.org (c) Copyright 2007, 2008, 2009, 2010, 2011 Sebastien Bourdeauducq This program is free software: you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation, version 3 of the License. I: BIOS CRC passed (93a2e549) BRD: SoC 1.1 on Milkymist One (PCB revision 2) BRD: Mem. card : Yes BRD: AC'97 : Yes BRD: PFPU : Yes BRD: TMU : Yes BRD: Ethernet : Yes BRD: FML meter : Yes BRD: Video in : Yes BRD: MIDI : Yes BRD: DMX : Yes BRD: IR : Yes BRD: USB : Yes BRD: Memtester : No TMU: texture mapping unit initialized USB: loading Navre firmware USB: starting host controller USB: HC: softusb-input v1.1 UKB: USB keyboard connected to console I: Displaying splash screen...USB: HC: Low speed device on port A USB: HC: Low speed device on port B OK USB: HC: VID: 0E6A, PID: 6001 USB: HC: VID: 093A, PID: 2510 USB: HC: Found keyboard USB: HC: Found mouse I: MAC address: 10:e2:d5:00:00:3a I: Press Q or ESC to abort boot I: Booting from filesystem... E: Unable to initialize memory card driver E: Unable to initialize filesystem I: Booting from flash... I: Loading 2033436 bytes from flash... I: Booting... RTEMS SHELL (Ver.1.0-FRC):/dev/console. Nov 13 2011. 'help' to list commands. [/] # memcard_disk_init: Error: SC = 27: Initialize memory card memcard_register: Error: SC = 27: Register disk memory card driver s# syslog: ftpd: FTP daemon startedD e(v3i csee:s s/idoenvs/ pmtayx0). . /dev/pty4 (5)pseudo-terminals registered. tted (3 sessions max) telnetd started with stacksize = 81920 and priority = 9 BOOTP timeout for server 255.255.255.255 BOOTP call failed -- Connection timed out BOOTP timeout for server 255.255.255.255 BOOTP call failed -- Connection timed out BOOTP timeout for server 255.255.255.255 BOOTP call failed -- Connection timed out III libHPDMC SDRAM initialization runtime (c) Copyright 2010 Sebastien Bourdeauducq, released under GNU LGPL version 3. Version 1.1 Initialization sequence completed. Autocalibration OK, testing memory... All SDRAM initialization completed, boot continuing. VGA: framebuffers at 0x440215c0 0x441a15c0 0x443215c0 VGA: DDC I2C bus initialized VGA: mode set to 640x480 MILKYMIST(tm) v1.1 BIOS http://www.milkymist.org (c) Copyright 2007, 2008, 2009, 2010, 2011 Sebastien Bourdeauducq This program is free software: you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation, version 3 of the License. I: BIOS CRC passed (93a2e549) BRD: SoC 1.1 on Milkymist One (PCB revision 2) BRD: Mem. card : Yes BRD: AC'97 : Yes BRD: PFPU : Yes BRD: TMU : Yes BRD: Ethernet : Yes BRD: FML meter : Yes BRD: Video in : Yes BRD: MIDI : Yes BRD: DMX : Yes BRD: IR : Yes BRD: USB : Yes BRD: Memtester : No TMU: texture mapping unit initialized USB: loading Navre firmware USB: starting host controller USB: HC: softusb-input v1.1 UKB: USB keyboard connected to console I: Displaying splash screen...USB: HC: Low speed device on port A USB: HC: Low speed device on port B OK USB: HC: VID: 0E6A, PID: 6001 USB: HC: VID: 093A, PID: 2510 USB: HC: Found keyboard USB: HC: Found mouse I: MAC address: 10:e2:d5:00:00:3a I: Press Q or ESC to abort boot I: Booting from filesystem... E: Unable to initialize memory card driver E: Unable to initialize filesystem I: Booting from flash... I: Loading 2033436 bytes from flash... I: Booting... RTEMS SHELL (Ver.1.0-FRC):/dev/console. Nov 13 2011. 'help' to list commands. [/] # memcard_disk_init: Error: SC = 27: Initialize memory card memcard_register: Error: SC = 27: Register disk memory card driver s# syslog: ftpd: FTP daemon startedD e(v3i csee:s s/idoenvs/ pmtayx0). . /dev/pty4 (5)pseudo-terminals registered. tted (3 sessions max) telnetd started with stacksize = 81920 and priority = 9 BOOTP timeout for server 255.255.255.255 BOOTP call failed -- Connection timed out BOOTP timeout for server 255.255.255.255 BOOTP call failed -- Connection timed out BOOTP timeout for server 255.255.255.255 BOOTP call failed -- Connection timed out II libHPDMC SDRAM initialization runtime (c) Copyright 2010 Sebastien Bourdeauducq, released under GNU LGPL version 3. Version 1.1 Initialization sequence completed. Autocalibration OK, testing memory... All SDRAM initialization completed, boot continuing. VGA: framebuffers at 0x440215c0 0x441a15c0 0x443215c0 VGA: DDC I2C bus initialized VGA: mode set to 640x480 MILKYMIST(tm) v1.1 BIOS http://www.milkymist.org (c) Copyright 2007, 2008, 2009, 2010, 2011 Sebastien Bourdeauducq This program is free software: you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation, version 3 of the License. I: BIOS CRC passed (93a2e549) BRD: SoC 1.1 on Milkymist One (PCB revision 2) BRD: Mem. card : Yes BRD: AC'97 : Yes BRD: PFPU : Yes BRD: TMU : Yes BRD: Ethernet : Yes BRD: FML meter : Yes BRD: Video in : Yes BRD: MIDI : Yes BRD: DMX : Yes BRD: IR : Yes BRD: USB : Yes BRD: Memtester : No TMU: texture mapping unit initialized USB: loading Navre firmware USB: starting host controller USB: HC: softusb-input v1.1 UKB: USB keyboard connected to console I: Displaying splash screen...USB: HC: Low speed device on port A USB: HC: Low speed device on port B OK USB: HC: VID: 0E6A, PID: 6001 USB: HC: VID: 093A, PID: 2510 USB: HC: Found keyboard USB: HC: Found mouse I: MAC address: 10:e2:d5:00:00:3a I: Press Q or ESC to abort boot I: Booting from filesystem... E: Unable to initialize memory card driver E: Unable to initialize filesystem I: Booting from flash... I: Loading 2033436 bytes from flash... I: Booting... RTEMS SHELL (Ver.1.0-FRC):/dev/console. Nov 13 2011. 'help' to list commands. [/] # memcard_disk_init: Error: SC = 27: Initialize memory card memcard_register: Error: SC = 27: Register disk memory card driver s# syslog: ftpd: FTP daemon startedD e(v3i csee:s s/idoenvs/ pmtayx0). . /dev/pty4 (5)pseudo-terminals registered. tted (3 sessions max) telnetd started with stacksize = 81920 and priority = 9 BOOTP timeout for server 255.255.255.255 BOOTP call failed -- Connection timed out BOOTP timeout for server 255.255.255.255 BOOTP call failed -- Connection timed out BOOTP timeout for server 255.255.255.255 BOOTP call failed -- Connection timed out IIH libHPDMC SDRAM initialization runtime (c) Copyright 2010 Sebastien Bourdeauducq, released under GNU LGPL version 3. Version 1.1 Initialization sequence completed. Autocalibration OK, testing memory... All SDRAM initialization completed, boot continuing. VGA: framebuffers at 0x440215c0 0x441a15c0 0x443215c0 VGA: DDC I2C bus initialized VGA: mode set to 640x480 MILKYMIST(tm) v1.1 BIOS http://www.milkymist.org (c) Copyright 2007, 2008, 2009, 2010, 2011 Sebastien Bourdeauducq This program is free software: you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation, version 3 of the License. I: BIOS CRC passed (93a2e549) BRD: SoC 1.1 on Milkymist One (PCB revision 2) BRD: Mem. card : Yes BRD: AC'97 : Yes BRD: PFPU : Yes BRD: TMU : Yes BRD: Ethernet : Yes BRD: FML meter : Yes BRD: Video in : Yes BRD: MIDI : Yes BRD: DMX : Yes BRD: IR : Yes BRD: USB : Yes BRD: Memtester : No TMU: texture mapping unit initialized USB: loading Navre firmware USB: starting host controller USB: HC: softusb-input v1.1 UKB: USB keyboard connected to console I: Displaying splash screen...USB: HC: Low speed device on port A USB: HC: Low speed device on port B OK USB: HC: VID: 0E6A, PID: 6001 USB: HC: VID: 093A, PID: 2510 USB: HC: Found keyboard USB: HC: Found mouse I: MAC address: 10:e2:d5:00:00:3a I: Press Q or ESC to abort boot I: Booting from filesystem... E: Unable to initialize memory card driver E: Unable to initialize filesystem I: Booting from flash... I: Loading 2033436 bytes from flash... I: Booting... RTEMS SHELL (Ver.1.0-FRC):/dev/console. Nov 13 2011. 'help' to list commands. [/] # memcard_disk_init: Error: SC = 27: Initialize memory card memcard_register: Error: SC = 27: Register disk memory card driver s# syslog: ftpd: FTP daemon startedD e(v3i csee:s s/idoenvs/ pmtayx0). . /dev/pty4 (5)pseudo-terminals registered. tted (3 sessions max) telnetd started with stacksize = 81920 and priority = 9 BOOTP timeout for server 255.255.255.255 BOOTP call failed -- Connection timed out BOOTP timeout for server 255.255.255.255 BOOTP call failed -- Connection timed out BOOTP timeout for server 255.255.255.255 BOOTP call failed -- Connection timed out II libHPDMC SDRAM initialization runtime (c) Copyright 2010 Sebastien Bourdeauducq, released under GNU LGPL version 3. Version 1.1 Initialization sequence completed. Autocalibration OK, testing memory... All SDRAM initialization completed, boot continuing. VGA: framebuffers at 0x440215c0 0x441a15c0 0x443215c0 VGA: DDC I2C bus initialized VGA: mode set to 640x480 MILKYMIST(tm) v1.1 BIOS http://www.milkymist.org (c) Copyright 2007, 2008, 2009, 2010, 2011 Sebastien Bourdeauducq This program is free software: you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation, version 3 of the License. I: BIOS CRC passed (93a2e549) BRD: SoC 1.1 on Milkymist One (PCB revision 2) BRD: Mem. card : Yes BRD: AC'97 : Yes BRD: PFPU : Yes BRD: TMU : Yes BRD: Ethernet : Yes BRD: FML meter : Yes BRD: Video in : Yes BRD: MIDI : Yes BRD: DMX : Yes BRD: IR : Yes BRD: USB : Yes BRD: Memtester : No TMU: texture mapping unit initialized USB: loading Navre firmware USB: starting host controller USB: HC: softusb-input v1.1 UKB: USB keyboard connected to console I: Displaying splash screen...USB: HC: Low speed device on port A USB: HC: Low speed device on port B OK USB: HC: VID: 0E6A, PID: 6001 USB: HC: VID: 093A, PID: 2510 USB: HC: Found keyboard USB: HC: Found mouse I: MAC address: 10:e2:d5:00:00:3a I: Press Q or ESC to abort boot I: Booting from filesystem... E: Unable to initialize memory card driver E: Unable to initialize filesystem I: Booting from flash... I: Loading 2033436 bytes from flash... I: Booting... RTEMS SHELL (Ver.1.0-FRC):/dev/console. Nov 13 2011. 'help' to list commands. [/] # memcard_disk_init: Error: SC = 27: Initialize memory card memcard_register: Error: SC = 27: Register disk memory card driver s# syslog: ftpd: FTP daemon startedD e(v3i csee:s s/idoenvs/ pmtayx0). . /dev/pty4 (5)pseudo-terminals registered. tted (3 sessions max) telnetd started with stacksize = 81920 and priority = 9 BOOTP timeout for server 255.255.255.255 BOOTP call failed -- Connection timed out BOOTP timeout for server 255.255.255.255 BOOTP call failed -- Connection timed out BOOTP timeout for server 255.255.255.255 BOOTP call failed -- Connection timed out II libHPDMC SDRAM initialization runtime (c) Copyright 2010 Sebastien Bourdeauducq, released under GNU LGPL version 3. Version 1.1 Initialization sequence completed. Autocalibration OK, testing memory... All SDRAM initialization completed, boot continuing. VGA: framebuffers at 0x440215c0 0x441a15c0 0x443215c0 VGA: DDC I2C bus initialized VGA: mode set to 640x480 MILKYMIST(tm) v1.1 BIOS http://www.milkymist.org (c) Copyright 2007, 2008, 2009, 2010, 2011 Sebastien Bourdeauducq This program is free software: you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation, version 3 of the License. I: BIOS CRC passed (93a2e549) BRD: SoC 1.1 on Milkymist One (PCB revision 2) BRD: Mem. card : Yes BRD: AC'97 : Yes BRD: PFPU : Yes BRD: TMU : Yes BRD: Ethernet : Yes BRD: FML meter : Yes BRD: Video in : Yes BRD: MIDI : Yes BRD: DMX : Yes BRD: IR : Yes BRD: USB : Yes BRD: Memtester : No TMU: texture mapping unit initialized USB: loading Navre firmware USB: starting host controller USB: HC: softusb-input v1.1 UKB: USB keyboard connected to console I: Displaying splash screen...USB: HC: Low speed device on port A USB: HC: Low speed device on port B OK USB: HC: VID: 0E6A, PID: 6001 USB: HC: VID: 093A, PID: 2510 USB: HC: Found keyboard USB: HC: Found mouse I: MAC address: 10:e2:d5:00:00:3a I: Press Q or ESC to abort boot I: Booting from filesystem... E: Unable to initialize memory card driver E: Unable to initialize filesystem I: Booting from flash... I: Loading 2033436 bytes from flash... I: Booting... RTEMS SHELL (Ver.1.0-FRC):/dev/console. Nov 13 2011. 'help' to list commands. [/] # memcard_disk_init: Error: SC = 27: Initialize memory card memcard_register: Error: SC = 27: Register disk memory card driver s# syslog: ftpd: FTP daemon started D(e3v iscees:s i/odnesv /mpatxy)0 . ./dev/pty4 (5)pseudo-terminals registered. ted (3 sessions max) telnetd started with stacksize = 81920 and priority = 9 BOOTP timeout for server 255.255.255.255 BOOTP call failed -- Connection timed out BOOTP timeout for server 255.255.255.255 BOOTP call failed -- Connection timed out BOOTP timeout for server 255.255.255.255 BOOTP call failed -- Connection timed out III libHPDMC SDRAM initialization runtime (c) Copyright 2010 Sebastien Bourdeauducq, released under GNU LGPL version 3. Version 1.1 Initialization sequence completed. Autocalibration OK, testing memory... All SDRAM initialization completed, boot continuing. VGA: framebuffers at 0x440215c0 0x441a15c0 0x443215c0 VGA: DDC I2C bus initialized VGA: mode set to 640x480 MILKYMIST(tm) v1.1 BIOS http://www.milkymist.org (c) Copyright 2007, 2008, 2009, 2010, 2011 Sebastien Bourdeauducq This program is free software: you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation, version 3 of the License. I: BIOS CRC passed (93a2e549) BRD: SoC 1.1 on Milkymist One (PCB revision 2) BRD: Mem. card : Yes BRD: AC'97 : Yes BRD: PFPU : Yes BRD: TMU : Yes BRD: Ethernet : Yes BRD: FML meter : Yes BRD: Video in : Yes BRD: MIDI : Yes BRD: DMX : Yes BRD: IR : Yes BRD: USB : Yes BRD: Memtester : No TMU: texture mapping unit initialized USB: loading Navre firmware USB: starting host controller USB: HC: softusb-input v1.1 UKB: USB keyboard connected to console I: Displaying splash screen...USB: HC: Low speed device on port A USB: HC: Low speed device on port B OK USB: HC: VID: 0E6A, PID: 6001 USB: HC: VID: 093A, PID: 2510 USB: HC: Found keyboard USB: HC: Found mouse I: MAC address: 10:e2:d5:00:00:3a I: Press Q or ESC to abort boot I: Aborted boot on user request BIOS> serialboot I: Attempting serial firmware loading sL5DdSMmkekro *** Milkymist One automated tests starting... *** Built: Dec 16 2011 at 16:21:51 (rev be5b0e7) *** Select a test category below, or hit ENTER to run all tests: a: Images b: SDRAM c: GPIO d: VGA e: Memory card f: Audio g: Ethernet h: Video input i: MIDI j: DMX512 k: Infrared l: USB *** a pressed Images CRC: soc-rescue.fpg CRC passed (got 67645429) bios-rescue.bin CRC passed (got 03b5889f) splash-rescue.raw CRC passed (got e8ff824f) flickernoise.fbi CRC passed (got 36fcc9db) soc.fpg CRC passed (got fac2ad92) bios.bin CRC passed (got 93a2e549) splash.raw CRC passed (got 978f860c) flickernoise.fbi CRC passed (got 36fcc9db) [  PASSED  ] *** Select a test category below, or hit ENTER to run all tests: a: Images b: SDRAM c: GPIO d: VGA e: Memory card f: Audio g: Ethernet h: Video input i: MIDI j: DMX512 k: Infrared l: USB