use TAIWAN JTAG cable libHPDMC SDRAM initialization runtime (c) Copyright 2010 Sebastien Bourdeauducq, released under GNU LGPL version 3. Version 1.0RC1 Initialization sequence completed. Autocalibration OK, testing memory... All SDRAM initialization completed, boot continuing. VGA: framebuffers at 0x441a33e0 0x443233e0 0x444a33e0 VGA: DDC I2C bus initialized VGA: mode set to 640x480 MILKYMIST(tm) v1.0RC1 BIOS http://www.milkymist.org (c) Copyright 2007, 2008, 2009, 2010 Sebastien Bourdeauducq This program is free software: you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation, version 3 of the License. I: BIOS CRC passed (7f7b4c54) BRD: SoC 1.0RC1 on Milkymist One (PCB revision 1) BRD: Mem. card : Yes BRD: AC'97 : Yes BRD: PFPU : Yes BRD: TMU : Yes BRD: Ethernet : Yes BRD: FML meter : Yes BRD: Video in : Yes BRD: MIDI : Yes BRD: DMX : Yes BRD: IR : Yes BRD: USB : Yes BRD: Memtester : No TMU: texture mapping unit initialized USB: loading Navre firmware USB: starting host controller USB: HC: softusb-input v1.0RC1 UKB: USB keyboard connected to console I: Displaying splash screen...USB: HC: Low speed device on port A USB: HC: Low speed device on port B OK I: MAC address: 10:e2:d5:00:00:08 I: Press Q or ESC to abort boot USB: HC: VID: 046D, PID: C062 USB: HC: VID: 04F2, PID: 0402 USB: HC: Found mouse USB: HC: Found keyboard USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) I: Aborted boot on user request BIOS> serialboot I: Attempting serial firmware loading sL5DdSMmkekro [FLTERM] Received firmware download request from the device. [FLTERM] Uploading kernel (58196 bytes)... [FLTERM] Upload complete (8.9KB/s). [FLTERM] Booting the device. [FLTERM] Done. *** Milkymist One automated tests starting... *** Running tests in category: SDRAM A8: [ PASSED ] A9: [ PASSED ] A10: [ PASSED ] A11: [ PASSED ] A12: [ PASSED ] Random pattern: [ PASSED ] Hammer pattern: [ PASSED ] Crosstalk pattern: [ PASSED ] *** Running tests in category: GPIO SW1: Press the button. f to fail test, s to skip. [ PASSED ] SW2: Press the button. f to fail test, s to skip. [ PASSED ] SW3: Press the button. f to fail test, s to skip. [ PASSED ] LED2: Is the LED on? (y/n/s) [ PASSED ] LED3: Is the LED on? (y/n/s) [ PASSED ] *** Running tests in category: VGA DDC: [ PASSED ] Test card: Is the picture OK? (y/n/s) [ PASSED ] *** Running tests in category: Memory card Card initialization: [ PASSED ] Block read: [ PASSED ] *** Running tests in category: Audio Codec probe: [ PASSED ] Line and headphones outputs: Is the test tone OK? (y/n/s/r) Is the test tone OK? (y/n/s/r) [ PASSED ] Microphone: Recording...Playing... Is the audio played back? (y/n/s/r) Recording...Playing... Is the audio played back? (y/n/s/r) [ PASSED ] Line input: Recording...Playing... Is the audio played back? (y/n/s/r) [ PASSED ] *** Running tests in category: Ethernet MDIO: Unexpected PHY ID: 0045 [ FAILED ] ARP resolution: [ PASSED ] *** Running tests in category: Video input Decoder probe: VIN: I2C bus initialized [ PASSED ] Capture: Press a key to start capturing Waiting for a captured frame. f to fail test, s to skip. LOCKS: 7 AD_RESULT: 4 Is the picture OK? (y/n) [ PASSED ] *** Running tests in category: MIDI Loopback: [ PASSED ] *** Running tests in category: DMX512 Loopback: [ PASSED ] *** Running tests in category: Infrared RC5 reception: Press the remote's "power" button... Waiting for remote. f to fail test, s to skip. [ PASSED ] *** Running tests in category: USB Port A: USB: loading Navre firmware USB: starting host controller USB: HC: softusb-input v1.0RC1 Press ENTER at the USB keyboard or press the left mouse button... USB: HC: Low speed device on port A USB: HC: Low speed device on port B USB: HC: VID: 046D, PID: C062 USB: HC: VID: 04F2, PID: 0402 USB: HC: Found mouse USB: HC: Found keyboard USB: HC: Transfer start: RX timeout error USB: HC: Control transfer failed: USB: HC: SETUP reply: USB: HC: (no data) [ PASSED ] Port B: Press ENTER at the USB keyboard or press the left mouse button... [ PASSED ] ******** TEST SUMMARY ******** Failed tests: - Ethernet/MDIO Skipped tests: 0 Failed tests: 1 Passed tests: 29 Total tests: 30 ******** SOME TESTS FAILED ******** *** Power off/reset board now...